How To Make Your Own Window Shades

How to Build Your Own Roller Shade

Introduction

These instructions demonstrate in detail how you lot can successfully build your own custom roller shade using a Fix My Blinds roller shade kit.

A Note on Rubber

Kids can strangle in blind cords. To make your blinds safer for kids, proceed cords out of attain and secure string and dewdrop chain loops. To learn more than, please visit our child rubber guide.

Tools Needed

Drill with Scrap Gear up

Tape Measure out

Needle Nose Pliers

Hack Saw with Miter Box

Parts Needed

Footstep 1 – Measure out the width of your window in three places, and utilize the smallest of these measurements.

Measure the length of your window in three places, and apply the largest of these measurements.
Use this guide when measuring your shade. The brackets and hardware have up ⅝" from each side.

Step 2 – Lay the decorative cloth face up on a flat surface and the liner on elevation.

If y'all are using a liner, please note that it is going to be 4" less than the decorative fabric.

Pace iii – Iron the fabric and then marker a ½" on the side where both fabrics meet.

Pin your marks and sew.
Repeat for both sides.

Step 4 – Center the fabric with the liner and each side should overlap ane ½".

Draw a line at the bottom ½" from the edge.
Pivot the fabrics together and run up.

Stride 5 – Turn the fabric within out.

Lay the cloth on a apartment surface with the decorative cloth facing down.
Iron to brand sure the edges are directly.

Step 6 – Fold the fabric over the hem bar 2 ½".

Remove the hem bar, and iron the fabric.
Draw a line ½" from the tiptop of the pocket and sew.

Stride 7 – Marker a line ½" inside the remaining un-sewn border and sew.

Step 8 – Mark your roller tube exactly one ¼" less than the overall width of the window.

Mark the hem bar 1" less than the length of the tube.
Cut both the tube and hem bar with a hacksaw and miter box.

Step ix – Insert the hem bar into the bottom pocket.

Pace 10 – Remove the tape from the adhesive strip on the aluminum tube.

Carefully line up the textile with the adhesive.

Step 11 – Roll the fabric over the top of the tube to operate as a contrary roll.

For a standard curlicue, the fabric volition gyre off the dorsum of the tube.

Step 12 – Insert the chain into the clutch past rotating information technology around the clutch gear.

Insert your clutch into the desired side of the tube.

Stride xiii – Firmly insert the terminate plug into the reverse side of the tube.

Stride 14 – Employ your pencil to mark the mounting location of the brackets.

Drill pilot holes with ⅛" drill bit into your marked locations.
Mount your brackets with screws.
Repeat steps for both sides.

Step 15 – Mountain your shade into the brackets and exam its functioning.

Footstep 16 – Marking and drill pilot holes for the tensioner.

Assemble the tensioner with the shine side of the locking insert facing out.
Attach the spring.

Step 17 – Screw the tensioner to the wall with your drill.

Insert the concatenation through the guide.

Pace 18 – Cut your chain to the desired length and connect the ends.

Apply the connector to attach the ends of the chain to create a loop.

Step xix – Ringlet the shade upwards to its highest point and take annotation of this bead location.

Utilize needle olfactory organ pliers to squeeze a crimp onto chain.
Roll the shade down to its lowest indicate and have note of this dewdrop location.
Use needle nose pliers to squeeze a crimp on that bead.

Stride twenty – Test your shade by raising and lowering it.

If necessary, conform your crimp locations.

Source: https://fixmyblinds.com/pages/how-to-build-your-own-roller-shade

Posted by: rezawhoored.blogspot.com